background image

Emptying the condensed
water container

The condensed water will be collected
in the condensed water container
unless the appliance has been fitted
with a drain hose (see installation).

Empty the condensed water
container after every drying
programme.

The drying programme will be
interrupted if the maximum level of the
condensed water container is reached.
A message will appear in the display.

^

Holding the container firmly in both
hands, as shown, pull it out slightly
towards the right-hand side.

^

Hold the container in a horizontal
position when carrying it.

^

Open the shutter and empty out the
water.

^

To replace the container, hold it at a
slight angle (as when removing it)
and push it in gently until you feel it
click into position.

^

To remove the message from the
display, switch the dryer off and then
on again.

Condensed water should not be
consumed. It could lead to health
problems for people and animals.

Condensed water can be put to
household use (e.g. used in a steam
iron or humidifier). To ensure that any
residual particles of fluff in the
condensed water are removed before
use, pass it through a fine sieve or
paper filter first.

Cleaning and care

26

Summary of Contents for T 8622 C

























































Reviews: