Miele T 8622 C Operating Instructions Manual Download | Manualshive

Page: 39 / 56

background image

In the event of any faults which you
cannot remedy yourself, or if the
machine is under guarantee, please
contact

– your Miele dealer or

– the Miele Service Department (see

back cover for contact details).

When contacting your dealer or the
Service Department, please quote the
model and serial number of your
machine, both of which are shown on
the data plate situated on the right
hand side below the drum aperture.

Future updates (PC)

The indicator or check light marked

PC

on the fascia panel is the interface
used by the Miele service technicians
during service work for testing
purposes and for updating the
machine's programme data.

Appliance guarantee

Please see the guarantee card
supplied with your machine.

Optional accessories

Optional accessories for this dryer are
available from your Miele Dealer or from
the Miele Spare Parts Department.

Please note that telephone calls may
be monitored and recorded for
training purposes.

After Sales service

39

«
...
37
38
39
40
41
...
»

Summary of Contents for T 8622 C

























































Reviews:

No comments

Related manuals for T 8622 C

MF200D80WB Series

Brand: Midea Pages: 44

Brand: Lucky Pages: 6

Brand: Linea 2000 Pages: 60

DOMO DELI FRYER XL 4 L

Brand: Linea 2000 Pages: 60

Brand: Kalorik Pages: 40

Brand: Mediclinics Pages: 80

Brand: Vulcan-Hart Pages: 2

Brand: Electrolux Pages: 12

Brand: Hotpoint Pages: 16

Brand: Bosch Pages: 44

Brand: Bosch Pages: 36

Brand: Bosch Pages: 40

Brand: Bosch Pages: 48

Brand: Bosch Pages: 40

Brand: Bosch Pages: 40

Brand: Bosch Pages: 40

Brand: Bosch Pages: 40

Brand: Bosch Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands