Miele T 8622 C Operating Instructions Manual Download | Manualshive

Page: 30 / 56

background image

Cleaning the condenser unit

Detergent residue, hair and fine fluff
from the dryer can get through the fluff
filters and block the condenser unit.
Dust from the room in which the dryer is
installed can also get into the
condenser unit and cause a blockage.

Check

the condenser unit at least

twice a year. Always check it if the

Clean out airways

message

appears. If the dryer is used
frequently then check the condenser
unit after approx. 100 drying cycles.
Clean it if necessary.

Removing the condenser unit

^

Open the service panel. Hold the
panel securely when doing this.

^

Now remove the panel by pulling it
diagonally upwards and place it to
one side.

^

Turn the lever on the inner cover
downwards to the vertical position.

^

Tilt the cover forwards.

^

Remove it by pulling it diagonally
upwards.

^

Turn the lever on the condenser unit
upwards to the vertical position.

Cleaning and care

30

«
...
28
29
30
31
32
...
»

Summary of Contents for T 8622 C

























































Reviews:

No comments

Related manuals for T 8622 C

Brand: Haier Pages: 10

Brand: Haier Pages: 7

Brand: Gastroback Pages: 23

Brand: inventum Pages: 24

DNH D8513AX-AUS

Brand: Hoover Pages: 15

Brand: Honey Can Do Pages: 3

Brand: Neumaerker Pages: 7

Brand: Vitek Pages: 20

MOVELING HV3820

Brand: TEFAL Pages: 2

Brand: Caple Pages: 28

Brand: Electrolux Pages: 12

Brand: AEG Pages: 40

Brand: AEG Pages: 52

Brand: AEG Pages: 44

Brand: AEG Pages: 40

Brand: AEG Pages: 76

Brand: AEG Pages: 44

Brand: AEG Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands