Miele T 8432 C Operating Instructions Manual Download Page 51

Page: 51 / 52

Keypad tone

An audible tone sounds each time a
button is pressed.

The machine is delivered with the
keypad tone deactivated. You can
activate it if wished.

Follow steps

to programme and

store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Press the

I-On/0-Off

button in.

Wait until the indicator light for the

Start/Stop

button lights up constantly . . .

. . . and then release the

Start/Stop

button.

Press the

Buzzer

button five times.

– The

Buzzer

indicator light will flash

on and off slowly once and will then
flash on and off quickly once.

–

and

(default setting) will flash

alternately in the display.

The number which appears alternately
in the display with

means:

Key pad tone is deactivated

(Default setting)

Key pad tone is activated

(the

Drying

indicator light will also

flash)

Pressing the

Start/Stop

button

switches from one to the other.

Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now
stored in memory. You can change it
again at any time.

Programmable functions

Summary of Contents for T 8432 C





















































Search results

Summary of Contents for T 8432 C

Reviews:

Related manuals for T 8432 C

Brands by name

Popular brands

Miele T 8432 C, Operating Instructions Manual

Search results

Summary of Contents for T 8432 C

Reviews:

Related manuals for T 8432 C

Brands by name

Popular brands