Miele T 8432 C Operating Instructions Manual Download Page 48

Page: 48 / 52

Memory function

The electronics will memorise the
drying level and any extra options
selected for the current drying
programme.

The Memory function

– is activated when the machine is

delivered. You can deactivate it if
wished.

– does not work if a programme is

cancelled or if Delay start has been
selected.

Follow steps

to programme and

store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Press the

I-On/0-Off

button in.

Wait until the indicator light for the

Start/Stop

button lights up constantly . . .

. . . and then release the

Start/Stop

button.

Press the

Buzzer

button twice.

– The

Buzzer

indicator light will briefly

flash on and off six times.

–

and

(default setting) will flash

alternately in the display.

The number which appears alternately
in the display with

means:

Memory activated

(the

Drying

indicator light will also

flash)

Memory deactivated

Pressing the

Start/Stop

button

switches from one to the other.

Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now
stored in memory. You can change it
again at any time.

Programmable functions

Summary of Contents for T 8432 C





















































Search results

Summary of Contents for T 8432 C

Reviews:

Related manuals for T 8432 C

Brands by name

Popular brands

Miele T 8432 C, Operating Instructions Manual

Search results

Summary of Contents for T 8432 C

Reviews:

Related manuals for T 8432 C

Brands by name

Popular brands