Miele T 8432 C Operating Instructions Manual Download Page 49

Page: 49 / 52

Extending the cooling down
time

The cooling down phase which takes
place before the end of a programme
can be lengthened if required. This
makes the garments easier to handle.

The dryer is delivered with the
extended cooling down time option
deactivated. You can extend the
cooling down time by 5 minutes or 10
minutes.

The option of extending the cooling
down time is available with the

Auto-

matic, Cottons, Minimum iron/Delicates,
Shirts

and

Denim

programmes.

Follow steps

to programme and

store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Press the

I-On/0-Off

button in.

Wait until the indicator light for the

Start/Stop

button lights up constantly ...

. . . and then release the

Start/Stop

button.

Press the

Buzzer

button three times.

– The

Buzzer

indicator light will briefly

flash on and off seven times.

–

and

(default settting) will flash

alternately in the display.

The number which appears alternately
in the display with

means:

The cooling down time is not
extended

(default setting).

The cooling down time will be five
minutes longer.

(The

Drying

indicator light will also

flash once).

The cooling down time will be ten
minutes longer.

(The

Drying

indicator light will also

flash twice).

Pressing the

Start/Stop

button

switches from one to the other.

Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now
stored in memory. You can change it
again at any time.

Programmable functions

Summary of Contents for T 8432 C





















































Search results

Summary of Contents for T 8432 C

Reviews:

Related manuals for T 8432 C

Brands by name

Popular brands

Miele T 8432 C, Operating Instructions Manual

Search results

Summary of Contents for T 8432 C

Reviews:

Related manuals for T 8432 C

Brands by name

Popular brands