Miele T 4453 C Operating Instructions Manual Download Page 50

Page: 50 / 52

Keypad tones

An audible tone sounds each time a
button is pressed.

The machine is delivered with the
keypad tone switched off. It can be
switched on if wished.

Follow steps

to programme and

store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Press the

I-On/0-Off

button in.

Wait until the

Start/Stop

indicator light

comes on . . .

. . . and then release the

Start/Stop

button.

Press the

Buzzer

button six times.

– The

Buzzer

indicator light will flash

on and off slowly once and will then
flash on and off quickly once.

–

and

will flash alternately in the

display
(factory default setting).

Press the

Start/Stop

button

repeatedly until

–

and

appear in the display

(the

Drying

indicator light will also flash):

Key pad tone switched on

–

and

appear in the display

Key pad tone off
(factory default setting)

Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now
stored in memory. To change the setting
repeat steps

Programmable functions

Summary of Contents for T 4453 C





















































Search results

Summary of Contents for T 4453 C

Reviews:

Related manuals for T 4453 C

Brands by name

Popular brands

Miele T 4453 C, Operating Instructions Manual

Search results

Summary of Contents for T 4453 C

Reviews:

Related manuals for T 4453 C

Brands by name

Popular brands