Miele T 4453 C Operating Instructions Manual Download Page 49

Page: 49 / 52

Extending the cooling down
time

The Cooling down phase which takes
place at the end of a programme can
be lengthend if required. This makes
the garments easier to handle.

The function for extending the Cooling
down phase

– is deactivated when the machine is

delivered. It can be activated if
wished.

– is only programmable on the

Cottons

and

Minimum iron

programmes.

Follow steps

to programme and

store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Press the

I-On/0-Off

button in.

Wait until the

Start/Stop

indicator light

comes on . . .

. . . and then release the

Start/Stop

button.

Press the

Buzzer

button four times.

– The

Buzzer

indicator light will briefly

flash on and off seven times.

–

and

will flash alternately in the

display
(factory default setting).

Press the

Start/Stop

button

repeatedly until

–

and

appear in the display

(the

Drying

indicator light will also flash

on and off once):
Cooling down phase -
5 minutes longer

–

and

appear in the display

(the

Drying

indicator light will also flash

on and off twice):
Cooling down phase -
10 minutes longer

–

and

appear in the display

Cooling down phase - normal
(factory default setting)

Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now
stored in memory. To change the setting
repeat steps

Programmable functions

Summary of Contents for T 4453 C





















































Search results

Summary of Contents for T 4453 C

Reviews:

Related manuals for T 4453 C

Brands by name

Popular brands

Miele T 4453 C, Operating Instructions Manual

Search results

Summary of Contents for T 4453 C

Reviews:

Related manuals for T 4453 C

Brands by name

Popular brands