Miele T 4453 C Operating Instructions Manual Download Page 42

Page: 42 / 52

Electrical connection

This tumble dryer is supplied ready for
connection to an a.c. single phase
supply. The machine is supplied with a
mains cable with moulded plug.

The appliance should be connected up
only by a qualified electrician, in
accordance with national and local
safety regulations.

For extra safety it is advisable to install
a residual current device (RCD) with a
trip current of 30 mA.

The voltage, rated load and plug rating
are given on the data plate. Please
ensure that these match the household
mains supply.

Important

The wires in the mains lead are
coloured in accordance with the
following code:

Green/yellow = earth
Blue = neutral
Brown = live

As the colours of the wires in the mains
lead of this appliance may not
correspond with the coloured markings
identifying the terminals in your plug,
proceed as follows:

The wire which is coloured green and
yellow must be connected to the
terminal in the plug which is marked
with the letter E or by the earth symbol

or coloured green or green and

yellow.

The wire which is coloured blue must
be connected to the terminal which is
marked with the letter N or coloured
black.

The wire which is coloured brown must
be connected to the terminal which is
marked with the letter A or coloured
red.

WARNING
THIS APPLIANCE MUST BE
EARTHED

Installation

Summary of Contents for T 4453 C





















































Search results

Summary of Contents for T 4453 C

Reviews:

Related manuals for T 4453 C

Brands by name

Popular brands

Miele T 4453 C, Operating Instructions Manual

Search results

Summary of Contents for T 4453 C

Reviews:

Related manuals for T 4453 C

Brands by name

Popular brands