Miele T 4453 C Operating Instructions Manual Download Page 23

Page: 23 / 52

The system lock prevents your
machine being used without your
knowledge.

It can be activated if wished.

The dryer's electronics are locked. The
dryer can still be switched on but a
programme cannot be started. The

locked

indicator light will flash if an

attempt is made to start a programme.

The door is not locked and can be
opened at any time.

To activate the lock

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Anti-crease

and DRYING

LEVEL buttons at the same time and
hold them pressed in until you reach
step

below.

Press the

I-On/0-Off

button in.

Press the

Short/Low temperature

button three times.

Then release the

Anti-crease

and

DRYING LEVEL buttons.

The

Locked

indicator light will flash.

The electronics have now been locked.

Switch the dryer off with the

I-On / 0-Off

button.

To deactivate the lock

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Anti-crease

and DRYING

LEVEL buttons at the same time and
hold them pressed in until you reach
step

below.

Press the

I-On/0-Off

button in.

Press the

Short/Low temperature

button three times.

Then release the

Anti-crease

and

DRYING LEVEL buttons.

The

Locked

indicator light will go out.

The electronics are no longer locked.

You can now use the dryer or switch

it off with the

I-On/0-Off

button.

Electronic system lock

Summary of Contents for T 4453 C





















































Search results

Summary of Contents for T 4453 C

Reviews:

Related manuals for T 4453 C

Brands by name

Popular brands

Miele T 4453 C, Operating Instructions Manual

Search results

Summary of Contents for T 4453 C

Reviews:

Related manuals for T 4453 C

Brands by name

Popular brands