Miele PWM 908 Operating And Installation Instructions Download Page 54

Page: 54 / 104

Changing the programme sequence

Adding or removing laundry

You can add or remove items during the
first few minutes after the programme
has started.



11:02



Coloured

items

Status

Time left

0:49



Main wash

Add laundry



Touch the

Add laundry

sensor control.

If the message

Add laundry

is not vis-

ible in the display then it is no longer
possible to add items of laundry.

The programme will stop and the door
will unlock.



Pull open the door.



Add laundry or remove individual
items.



Close the door.



Touch the

Start/Stop

sensor control.

The programme will continue.

The safety lock will remain activated if
the temperature in the drum is above
55 °C. The lock will not deactivate un-
til the temperature has dropped to be-
low 55 °C.

Summary of Contents for PWM 908









































































































Search results

Summary of Contents for PWM 908

Reviews:

Related manuals for PWM 908

Brands by name

Popular brands

Miele PWM 908, Operating And Installation Instructions

Search results

Summary of Contents for PWM 908

Reviews:

Related manuals for PWM 908

Brands by name

Popular brands