Miele PW 5105 Vario Operating And Installation Instructions Download Page 26 | Manualshive

Page: 26 / 60

background image

Rinse hold

The laundry is not spun after the last rinse and remains
suspended in the final rinse water. This reduces creasing if
the laundry is not going to be removed from the drum imme-
diately after the end of the programme.

Intensive*

For heavy soiling or where staining is visible.

The duration of the main wash and of the rinses is increased.

Water plus*

The machine is set at the factory so that the water level in the
main wash and rinses will be increased if the

Water plus

extra

option is selected.

However, you can select other settings for

Water plus

. See

the separate booklet supplied with the machine for details
under

Settings/Supervisor level

.

*

Intensive

and

Water plus

have to be set in the

Settings/Supervisor level

menu.

Any extras that are available for a programme will be listed
in the Extras sub-menu. If an extra is not displayed, it is
not available for use with the programme selected.

Extras

26

«
...
24
25
26
27
28
...
»

Summary of Contents for PW 5105 Vario





























































Reviews:

No comments

Related manuals for PW 5105 Vario

Brand: Favor.it Pages: 9

Brand: Makita Pages: 113

Brand: Logik Pages: 40

Brand: Hoover Pages: 15

Hydra-Clean 1235 800-268

Brand: Graco Pages: 24

Brand: Amica Pages: 52

Brand: Jet-tech Pages: 10

Brand: Magic Chef Pages: 12

Brand: Daewoo Pages: 36

Brand: M-system Pages: 109

Brand: Furrion Pages: 26

Brand: Kärcher Pages: 112

Brand: Euromaid Pages: 31

MF200D80WB Series

Brand: Midea Pages: 44

Brand: Infiniton Pages: 67

Brand: Hotpoint Pages: 16

Brand: Silverline Pages: 76

Brand: LVO Manufacturing Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands