Miele PW 5105 Vario Operating And Installation Instructions Download Page 50 | Manualshive

Page: 50 / 60

background image

Installation on a raised plinth

The machine can be installed on a steel
plinth base (available open or closed)
or on a concrete plinth.

,

If the machine is installed on an

on-site concrete or brick plinth, it

must

be secured using the clamps

supplied with the machine.
Otherwise there is the danger of the
machine moving and falling off the
plinth during spinning.

^

Secure the front feet of the machine
with the clamps supplied.

^

Follow the fitting instructions
supplied.

Payment system

This machine can be fitted with a
payment system.*

The payment system can be set up by
the Miele technician or authorised
dealer when the machine is
commissioned.

Coins / tokens must be removed
from the payment system regularly,
otherwise it will become blocked.

* These can be obtained from the Miele
Spare Parts department.

Installation

50

«
...
48
49
50
51
52
...
»

Summary of Contents for PW 5105 Vario





























































Reviews:

No comments

Related manuals for PW 5105 Vario

Brand: Haier Pages: 20

Brand: PARRY Pages: 15

Brand: Cookology Pages: 24

Computer Control 1100 A3268

Brand: Hoover Pages: 12

Brand: Ariston Pages: 16

Brand: V-ZUG Pages: 36

Brand: Maytag Pages: 13

Brand: Bellini Pages: 43

Brand: FAIP Pages: 32

Brand: Greencut Pages: 52

Brand: Sealey Pages: 5

Brand: ZANKER Pages: 9

Brand: Indesit Pages: 60

Brand: Asko Pages: 52

Brand: Thermador Pages: 66

Brand: Supra Pages: 24

Brand: Briggs & Stratton Pages: 2

Brand: Maytag Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands