manualshive.com logo in svg

Miele PT 7135 C, Operating And Installation Instructions

Share
Download
Miele PT 7135 C Operating And Installation Instructions Download Page 42

Installation site

,

Make sure the dryer door can be

opened without hindrance after
installation.

Transporting the machine to its
installation site

When moving the machine you can
hold it by the lid where it protrudes to
the rear of the dryer. To manoeuvre the
dryer out of its packing case to its
installation site you will also need to
hold it by the front feet.

Levelling the machine

The machine must be perfectly level to
ensure safe and proper operation.

^

The screw feet can be adjusted to
compensate for any unevenness in
the floor.

,

The ventilation gaps in the plinth

and the front panel must not be
covered over as this would prevent a
sufficient intake of air.

This tumble dryer is not suitable for
building under.

Room in which the dryer is located

Air taken in for use in the drying
process will be warm when it is
expelled from underneath the dryer.
This expelled air heats up the air in the
room. It is therefore very important to
ensure that the room is adequately
ventilated, particularly if the dryer is
located in a small room. Otherwise
running times and energy consumption
could be increased.

Installation and connection

42

Summary of Contents for PT 7135 C

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands