manualshive.com logo in svg

Miele PT 7135 C, Operating And Installation Instructions

Share
Download
Miele PT 7135 C Operating And Installation Instructions Download Page 12

Programme selection menu

Programme

Back

A

selection

Cottons

Minimum iron
Woollens handcare

H

^

By turning the multi-function selector you can select any
programme. The highlighting will move up or down
depending on the direction the multi-function selector is
turned in.

The

V

H

arrows on the right of the display indicate the

direction and further options.

^

Pressing the multi-function selector takes you to the

main

menu

of the drying programme selected.

Drying programme main menu

Cottons

Normal

Duration: 1:16 h

Low temp.

H

Timer

Y

H

Save

H

Back

A

H

^

Turn the multi-function selector to highlight either the
"Drying level" or the "Programme".

– Everything in the display (including

Low temp., Timer,

Save, Back

) can be highlighted and then confirmed by

pressing the multi-function selector.

Settings menu

J

The

Settings

menu

J

is used to alter the tumble dryer's

electronics to suit different requirements.

Operating the tumble dryer

12

Summary of Contents for PT 7135 C

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands