manualshive.com logo in svg

Miele PT 7135 C, Operating And Installation Instructions

Share
Download
Miele PT 7135 C Operating And Installation Instructions Download Page 38

In the event of any faults which you
cannot remedy yourself, or if the
machine is under guarantee, please
contact

– your Miele dealer, or

– the Miele Service Department

(see back cover for contact details).

When contacting the your dealer or the
Service Department, please quote the
model and serial number of your
machine, both of which are shown on
the data plate situated on the right
hand side below the drum aperture.

PC / Optical interface

The indicator or check light marked

PC

on the fascia panel is the interface
used by Miele service technicians
during servicing work for testing
purposes and for undating the
machine's programme data.

Optional accessories

Optional accessories for this dryer are
available from your Miele Dealer or from
the Miele Spare Parts Department.

Please note that telephone calls may
be monitored and recorded for
training purposes.

After sales service

38

Summary of Contents for PT 7135 C

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands