Miele PT 7135 C Operating And Installation Instructions Download Page 23

Page: 23 / 56

Woollens hand care

Max. load: 2.5 kg*

Fabric
type

Woollen fabrics.

Notes

–

To refresh and fluff up woollen garments quickly. Woollen fabrics
are not dried completely by this programme.

–

Remove garments as soon as the programme has finished and
leave to finish drying at room temperature.

Smoothing

Max. load: 3.0 kg*

Fabric
type

–

Cotton and linen fabrics.

–

Minimum iron items made of mixed fibres, cottons or synthetics,
e.g. trousers, jackets, shirts.

Notes

–

Smooths out creasing caused during the spin cycle in the washing
machine.

–

Fabrics are not completely dried in this programme. Remove
garments as soon as the programme has finished and leave to
finish drying at room temperature.

Cool air

Max. load: 6.5 kg*

Fabric
type

Any item which only needs airing.

Warm air

Max. load: 6.5 kg*

Fabric
type

–

"Voluminous" or multi-layered fabrics whose layers have different
drying characteristics, e.g. jackets, pillows.

–

For drying individual items, e.g. bath towels, bathing costumes,
tea-towels.

Notes

–

Select

Low temperature

for fabrics with the

symbol.

–

Do not select the longest drying time to start with. Check the items
as you are drying them to find the optimum time.

* Weight of dry laundry

Programme chart

Summary of Contents for PT 7135 C

























































Search results

Summary of Contents for PT 7135 C

Reviews:

Brands by name

Popular brands

Miele PT 7135 C, Operating And Installation Instructions

Search results

Summary of Contents for PT 7135 C

Reviews:

Brands by name

Popular brands