manualshive.com logo in svg

Miele PG 8581, Operating Instructions Manual

Share
Download
Miele PG 8581 Operating Instructions Manual Download Page 122

Frequently asked questions

122

Spray arm monitoring/wash pressure

Problem

Possible cause and solution

Spray arm monitoring - Upper
spray arm: Spray arm blocked
or excessive foaming

or 

Spray arm monitoring - Lower
spray arm: Spray arm blocked
or excessive foaming

or

Spray arm monitoring - mobile
unit spray arm 1 - : spray arm
blocked or excessive foaming

The set spin speed has not been reached.
– Wash items are obstructing the machine or basket spray
arms.

Arrange the wash items so that the spray arms can turn
easily and start the program again.

– The relevant spray arm is blocked.

Clean the spray arm.

Check whether the filters in the wash cabinet are clean
and correctly inserted.

Start the program again.

– Wash pressure is too low due to a heavy build-up of
foam.

Follow the instructions regarding foam build-up in
“Chemical processes and technology”.

Start the 

Rinse

 program to clean the wash cabinet.

Then reprocess the wash items again.

Spray pressure exceeds tol-
erance

The wash pressure differs from the reference value. 
Possible causes of fluctuations in the wash pressure in-
clude:
- defective water connections,
- open adapters,
- foam build-up.

Identify and resolve the cause of this.

The program is not interrupted. Nevertheless, you must
reprocess the load.

Spray pressure fluctuating too
much

A program was interrupted because of severe fluctuations
in the wash pressure. 
Possible causes of fluctuations in the wash pressure in-
clude:
- defective water connections,
- open adapters,
- foam build-up.

Identify and resolve the cause of this.

Reprocess the load again.

Summary of Contents for PG 8581

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands