Miele PG 8527 Operating Instructions Manual Download Page 55

Page: 55 / 84

Scanning the load

When Scan the load is activated, the following message will
appear to prompt the operator to scan the load:

Scan the load

Scan the first barcode on the load.

The barcode numbers of the scanned load will be listed in the
menu

Scan the load

0987664

Scan any other barcodes if necessary.

If a barcode has already been scanned, the following
question will appear in the display:

Load already scanned. Accept?

A maximum of 99 load barcodes can be scanned. The
following message will then appear:

Max. number of entries reached

You can use

to delete the last entry on the list. To avoid

deleting an entry inadvertently, the following "Are you sure"
question must be answered:

Delete last entry?

Barcode scanner (optional)

Summary of Contents for PG 8527





















































































Search results

Summary of Contents for PG 8527

Reviews:

Related manuals for PG 8527

Brands by name

Popular brands

Miele PG 8527, Operating Instructions Manual

Search results

Summary of Contents for PG 8527

Reviews:

Related manuals for PG 8527

Brands by name

Popular brands