Miele G1574 Operating Instructions Manual Download Page 52

Page: 52 / 76

The dishwasher does not fill/drain

Problem

Possible cause

Remedy

The In-operation
indicator is flashing
quickly.
The buzzer is
sounding.
The Inlet/Drain
indicator flashes when
the door is open.

The tap is
closed.

– Open the tap fully.

The dishwasher stops
during a programme.
The In-operation
indicator is flashing
quickly.
The buzzer sounds.
The Inlet/Drain
indicator flashes when
the door is open.
Fault code FXX shows
in the display.

Before rectifying the problem you
must:

– Switch the dishwasher off with

the Off button

Fault F12/F13:
Water intake is
restricted.

– Open the tap fully.

– Clean the water inlet filter (see

Maintenance).

– The water pressure at the intake

is lower than 30 kPa (0.3 bar).
Seek professional advice.

Fault F11:
Water outlet is
restricted, water
remains in the
wash cabinet at
the end of a
programme.

– Clean the filter combination. See

Cleaning and care.

– Clean the drain pump. See

Maintenance.

– Clean the non-return valve. See

Maintenance.

– Remove any kink in the drain

hose.

Problem solving guide

Summary of Contents for G1574













































































Search results

Summary of Contents for G1574

Reviews:

Related manuals for G1574

Brands by name

Popular brands

Miele G1574, Operating Instructions Manual

Search results

Summary of Contents for G1574

Reviews:

Related manuals for G1574

Brands by name

Popular brands