Miele G1574 Operating Instructions Manual Download Page 50

Page: 50 / 76

With the aid of the following guide, minor problems can be easily corrected
without contacting Miele.

The following information may help you to find the reason for a fault, and to correct
it. Please note:

Installation work and repairs to electrical appliances must only be carried

out by a suitably qualified and competent person in strict accordance with
current local and national safety regulations. The manufacturer cannot be held
liable for unauthorised work.

Technical problems

Problem

Possible cause

Remedy

The dishwasher does
not start.

The door is not properly
closed.

Push the door firmly shut.

The appliance is not
plugged in.

Insert the plug and switch on
at the socket.

The fuse is defective or
has tripped.

Reset or replace the fuse.
(Minimum fuse rating - see
data plate).

The appliance is not
switched on.

Press the On button

and

select a programme.

The dishwasher
stops during a
programme.

The fuse is defective or
has tripped.

Reset or replace the fuse.

After the programme
has started, the
In-operation indicator
light is not visible.

The reflector panel was
not correctly fitted.

Re-fit the reflector panel
correctly (see Installation
diagram).

Problem solving guide

Summary of Contents for G1574













































































Search results

Summary of Contents for G1574

Reviews:

Related manuals for G1574

Brands by name

Popular brands

Miele G1574, Operating Instructions Manual

Search results

Summary of Contents for G1574

Reviews:

Related manuals for G1574

Brands by name

Popular brands