Miele CVA 2650 Operating Instructions Manual Download Page 71

Page: 71 / 105

Programming

The appliance must be correctly
installed and connected before the
first use.

Setting the language

Press the left jog shuttle to turn the
machine on.

Míele

Welcome!

When turned on for the first time, a
welcome screen as well as other
messages will appear in the right
display. The welcome screen will be
displayed each time the machine is
turned on until 5 drinks (including
steam) have been prepared.

COSI

2 3 4 5

o n

The displays light.

You will then be prompted to select a
language.

Turn the right jog shuttle until the
desired language shows in the
display.

Press the right jog shuttle to confirm.

To turn off the machine

Press the left jog shuttle until the
displays go dark.

Installation

www.dexpress.com

Page 71 of 105

12/31/2010

www.dexpress.com

Page 71 of 105

12/31/2010

CVA2650

Mfr Sup

Summary of Contents for CVA 2650










































































































Search results

Summary of Contents for CVA 2650

Reviews:

Related manuals for CVA 2650

Brands by name

Popular brands

Miele CVA 2650, Operating Instructions Manual

Search results

Summary of Contents for CVA 2650

Reviews:

Related manuals for CVA 2650

Brands by name

Popular brands