Miele CVA 2650 Operating Instructions Manual Download Page 20 | Manualshive

Page: 20 / 105

Miele CVA 2650 Operating Instructions Manual Download Page 20

Turning the machine on and off

The appliance must be correctly
installed and connected before the
first use.

Turning on

^

Press the left jog shuttle.

Míele

Welcome!

When turned on for the first time, a
welcome screen as well as other
messages will appear in the right
display. The welcome screen will be
displayed each time the machine is
turned on until 5 drinks (including
steam) have been prepared.

COSI

K

1

2 3 4 5

L

o n

G

k

C

The displays light.

Turning off

^

Press the left jog shuttle until the
displays go dark.

If the automatic rinsing function is
activated, both displays will go dark
when turned off. If coffee was
dispensed, the machine will be
rinsed and "Machine Rinsing" will
appear in the right display. When
finished the machine will shut off
completely.

First steps to use

11

www.dexpress.com

Page 20 of 105

12/31/2010

www.dexpress.com

Page 20 of 105

12/31/2010

CVA2650

CVA2650

Mfr Sup

Mfr Sup

«
...
18
19
20
21
22
...
»

Summary of Contents for CVA 2650










































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands