Miele CVA 2650 Operating Instructions Manual Download Page 29

Page: 29 / 105

Cappuccinatore (milk froth
mug)

A cappuccinatore (milk froth mug) is
supplied with the appliance.

Before using the cappuccinatore for
the first time, wash it either in the
dishwasher or with hot water and
liquid dish soap.
See "Common coffee system care".

The cappuccinatore has a valve,

over the handle and a spout on its side,

Cold, whole milk is best for creating
froth. The higher the fat content, the
better the froth.

The steam is regulated by turning the
valve:

Hot milk is prepared

Froth is prepared

Turn the spout so that the black dot
points to the respective symbol.

Milk is frothed

into the cup

into the cappuccinatore

Making coffee

www.dexpress.com

Page 29 of 105

12/31/2010

www.dexpress.com

Page 29 of 105

12/31/2010

CVA2650

Mfr Sup

Summary of Contents for CVA 2650










































































































Search results

Summary of Contents for CVA 2650

Reviews:

Related manuals for CVA 2650

Brands by name

Popular brands

Miele CVA 2650, Operating Instructions Manual

Search results

Summary of Contents for CVA 2650

Reviews:

Related manuals for CVA 2650

Brands by name

Popular brands