Miele 4002516488002 Operating Instructions Manual Download Page 50

Page: 50 / 76

Problem solving guide

The drying cycle duration is very long

Problem

Cause and remedy

The drying process
goes on too long or
even switches off.*

The room where the tumble dryer is located is too
warm.



Ventilate the room thoroughly.

Detergent residues, hair and fine fluff can clog the fil-
ters.



Clean the fluff filters and the plinth filter.



Remove visible fluff from the heat exchanger.

The laundry is unevenly distributed or has rolled up.
The drum is too full.



Disentangle the laundry and remove a few items.



Start a programme.

The bottom right grille is blocked.



Move any objects, such as a laundry basket, away
from the dryer.

The laundry is too damp.



Spin using a higher spin speed in the washing ma-
chine.

Metallic components, e.g. zips, have prevented the
tumble dryer from registering the correct laundry
moisture level.



Open any zips next time.



If the problem recurs, dry these items using the

Warm air/DryFresh

programme.

* Switch the tumble dryer off and on again before starting a new programme.

Summary of Contents for 4002516488002













































































Search results

Summary of Contents for 4002516488002

Reviews:

Related manuals for 4002516488002

Brands by name

Popular brands

Miele 4002516488002, Operating Instructions Manual

Search results

Summary of Contents for 4002516488002

Reviews:

Related manuals for 4002516488002

Brands by name

Popular brands