Miele 4002516488002 Operating Instructions Manual Download Page 24

Page: 24 / 76

2. Load the tumble dryer

Loading the laundry

Preventing damage to fabrics.
Before loading the dryer, read “1.
Notes on correct laundry care”.



Open the door.



Remove any items that have been left
inside the drum.



Unfold the laundry and load loosely
into the drum.

Do not overload the drum. Doing so
will cause unnecessary wear and tear
to the laundry and affect the drying
result. It is also likely to cause more
creasing.

Laundry items may be damaged if
they get trapped by the door.

Checking the FragranceDos socket

If you are not using a fragrance flacon,
check that the FragranceDos socket is
closed.

The “Fragrance flacon” chapter de-
scribes how to use the fragrance
flacon.



Push the tab down completely (see
arrow) so that the socket is closed.
Otherwise, fluff will accumulate here.

Close the door



Shut the door with a gentle swing.

Summary of Contents for 4002516488002













































































Search results

Summary of Contents for 4002516488002

Reviews:

Related manuals for 4002516488002

Brands by name

Popular brands

Miele 4002516488002, Operating Instructions Manual

Search results

Summary of Contents for 4002516488002

Reviews:

Related manuals for 4002516488002

Brands by name

Popular brands