To service Shifter. ,
Refer to the Control Pod,
B u t t o n s
and
Service
Switch off the power to the game machine and unplug the AC line cord
Remove the 4 tamper-resistant buttons used to fasten the faceplate.
Pull the plate forward enough to expose the
NOTE:
out of the
pod
quite
a bit
of force.
Label and disconnect the wiring for the pod(s) being serviced.
assembly completely out of the pod and set aside.
Perform the-desired repair
or
equipment replacement.
Reconnect wires and re-install shifter. NOTE: Orient
the
mechanism on
edge of the
toward the
floor and insert
pod followed by the top edge to fully seat.
Check for
wires.
Fasten the faceplate with the screws provided.
To service Steering Assembly.. ,
Refer to the Steering
A s s e m b l y
i l l u s t r a t i o n .
Switch off the power to the game machine and unplug the AC line cord.
Remove the Dashboard.
Refer
s e r v i c e
for
Dashboard.
Remove 6 screws used to fasten the cover plate to the center of the steering wheel.
Remove the cover plate and set aside.
Remove the 3 screws used to fasten the wheel hoop to the shaft. Pull the wheel hoop off
of the dashboard.
Remove 4
flange nuts holding the motor shield, motor and shaft to the wheel assembly
(Presence of motor shield not required on all cabinet styles).
3
Slide the motor and the shaft off of the assembly.
Perform the desired repair or equipment replacement.
R e - i n s t a l l a n d f a s t e n a l l i t e m s i n p l a c e w r t h t h e s c r e w s p r o v i d e d .
While the steering mechanism is exposed, Inspect the belt for splits in the rubber or other
signs of wear at the edges of the teeth. Install a new belt if necessary following the
i n s t r u c t i o n s b e l o w .
To service Steering Assembly.. .
Loosen four
nuts for the motor bracket.
T i g h t e n t h e t e n s i o n - a d j u s t b o l t o n l y u n t i l t h e r e i s n o b e l t d e f l e c t i o n , t h e n l o o s e n t h e b o l t
one full turn and tighten the four nuts.
Reattach the
and recalibrate the assembly.
IMPORTANT: Apply removable anaerobic adhesive thread lock (Loctite Blue 242 or
equivalent) and torque set screw to seven to nine ft.-lbs. (84 to 108 tn.-lbs.)
w a s l o o s e n e d ( s e e i l l u s t r a t i o n ) .
Service
Summary of Contents for 40272
