background image

GR8-1200 OEM

Midtronics Inc.     7000 Monroe Street     Willowbrook, IL 60527

www.midtronics.com

5

1  General Safety Precautions

1.  IMPORTANT SAFETY INSTRUCTIONS.  

IT

 

I

O

UT

M

O

S

T

 

I

MP

ORTANCE

 

THAT

  B

E

F

ORE

 

U

S

ING

 

YOUR

 

CHARGER

YOU

 

READ

 

THI

S M

ANUAL

 

AND

  F

OLLOW

 

THE

  S

A

F

ETY

 

AND

 

O

P

ERATING

 

IN

S

TRUCTION

E

X

ACTLY

SAVE THESE 

INSTRUCTIONS.

Risk of explosive gases

Batteries generate explosive gases during 

normal operation, and when discharged or 

charged.

1.1  To reduce risk of battery explosion, follow these safety 

instructions and those published by the battery manu-
facturer and the manufacturer of any equipment you in-
tend to use in the vicinity of a battery. Review cautionary 
marking on these products and on the engine, and on the 
vehicle or equipment containing the battery.

Charging a non-rechargeable battery 

may cause the battery to burst.

To reduce the risk of injury, only charge 

rechargeable lead-acid type batteries including 

maintenance-free, low-maintenance, or deep-

cycle batteries.

If you are uncertain as to the type of battery you are 
attempting to charge, or the correct procedure for checking 
the battery’s state of charge, contact the seller or battery 
manufacturer.

1.2  Use of an attachment not recommended or sold by the 

battery charger manufacturer may result in a risk of fi re, 
electric shock, or injury to persons.

1.3  To reduce risk of damage to the electric plug and cord, 

pull by the plug rather than by the cord when disconnect-
ing the charger.

1.4  Position the AC and DC leads to avoid tripping over them 

and to prevent damage by hood, doors, or moving engine 
parts; protect from heat, oil, and sharp edges.

1.5  Do not operate the charger if it has received a sharp blow, 

been dropped or otherwise damaged in any way; take it 
to a qualifi ed service center.

1.6  Do not disassemble charger; take it to a qualifi ed service 

center when repair is required. Incorrect reassembly may 
result in a risk of electric shock or fi re.

1.7  To reduce risk of electric shock, unplug the charger from 

the AC outlet before attempting any maintenance or 
cleaning. Turning off  the controls will not reduce this risk.

Remove marine “boat” batteries and 

charge them on shore.

Charging marine batteries on-board requires 

specially designed equipment for marine use.

1.8  Connect and disconnect the battery leads only when the 

AC supply cord is disconnected. 

1.9  Do not overcharge the battery. (See sections 3 and 10 in 

the safety instructions)

1.10  Charge the battery in a dry, well-ventilated area.

1.11 Never place articles on or around the charger, or locate 

the charger in a way that will restrict the fl ow of cooling 

air through the cabinet.

1.12  An extension cord should not be used unless absolutely 

necessary. (See paragraph 4.3.)

1.13  Have a damaged cord or plug replaced immediately.

1.14  Do not expose the charger to rain or snow.

2 Personal 

Precautions

2.1  Always have someone within range of your voice, or close 

enough to come to your aid, when working around lead 
acid batteries. 

2.2  Have plenty of fresh water and soap nearby in case bat-

tery acid contacts skin, clothing or eyes.

2.3  Wear complete eye protection, clothing protection, and 

wear rubber soled shoes. Place damp cloth over battery 
to protect against acid spray. When ground is very wet or 
covered with snow, wear rubber boots. Avoid touching 
eyes while working near battery.

2.4  If battery acid contacts skin or clothing, wash immediately 

with soap and water. If acid enters the eye, immediately 
fl ush with cold running water for at least 10 minutes, and 
seek medical attention.

2.5  NEVER smoke or allow a spark or fl ame in vicinity of a bat-

tery or engine.

2.6  Be extra cautious to reduce risk of dropping a metal tool 

onto the battery. It might spark or short circuit the battery 
or other electrical part that may cause an explosion.

2.7  Before working with a lead-acid battery, remove personal 

metal items such as rings, bracelets, necklaces, watches, 
etc. A lead-acid battery can produce a short circuit current 
high enough to weld such items causing a severe burn.

Safety Instructions

!

Safety Guidlines

Summary of Contents for GR8-1200 OEM























































Reviews: