Midea WF130 User Manual Download Page 15

- 15 - 

Operation Noise 

Normal Noise 

Hum – the noise is cause by operation of the refrigeration unit. 

Coo, rumbling or gurgle – the noise is caused by flow of cooling agent in the 

pipeline. 

Noise that can be removed easily 

The noise caused by unevenness of placement of Beverage Cooler 

You can use gradienter to correct and level the Beverage Cooler. You can use 

screw leg to level it or you can place mat under the Beverage Cooler to level it. 

 

The noise generated when the Beverage Cooler leans against other furniture. 

Move the Beverage Cooler  away from the furniture or equipment, against 

which the Beverage Cooler leans. 

 

The noise caused by mutual touch of vessels 

Slightly separate the bottles or vessels from each others 

 

Troubleshooting By Yourself 

Before you call the after-sales service phone number, please check if you are 

able to remove the failures according to the following hints. 

Failures 

Possible Causes 

Remediation Measures 

Temperature is quite 

different from setting 

value 

 

Sometimes, the problem 
can be removed if you 
just turn off power of the 
Beverage Cooler for 5 
minutes and then restart 
it. 
If the temperature is too 
high, you can check it 
several hours later to 
see if the temperature is 
consistent with the 

Summary of Contents for WF130

















Reviews: