background image

      Trouble Shooting

The

 

start

 

of

 

the

 

appliance

 

does

 

not

 

work or

 

it

 

stops

 

during

 

operation

.

First

 

try

 

to

 

find

 

a

 

solution

 

to

 

the

 

problem, If

 

not

contact

 

the

 

service centre

.

Description

10

19

    No 

 

washing

Inspection Items

If the power is off or the fuse is burned out.
If the power supply voltage is too low.
If the water amount reaches to the required water level.(The washer will 
   not work if the water amount does not reach the required water level)
If it is set to "Delay" washing mode. (It will only start to work until the 
   reservation time reached)  

No water 

 

flows in

If the power is off or the fuse is burned out.
If the water supply is cut off or the water pressure is too low.
If the inlet hose is properly connected and the water tap is opened.
If the filtering screen of inlet valve is blocked by dirt.
If the coil of inlet valve is damaged. (The slight electromagnetic sound is 
normal phenomenon when the inlet valve is switched on)
If the "Start / Pause" button is pressed after the power switch is pressed.  

Abnormal 

 

draining

If the water drain hose is placed very high.
If the end of water drain hose  is sealed in pond.
If the internal rubber ring of drain valve is blocked by dirt.

Abnormal 

 

spin

If the door lid is closed.
If all clothing piled largely at one side of barrel or the clothing is excessively
   placed.
If the washer is not placed in stable condition or it is placed in inclination 
   state. (The ground is not flat).
If the motor belt is loosened.   

MAINTENANCES

•   

or the

 

display

 

    

shows

 

other

 

alarm

 

codes 

After

 

the

 

check

activate

 

the

 

appliance

If

 

the

 

problem

 

occurs

 

again

contact

 

the service. 

Note!

Description

Reason

Solution

Please try again first, call up service
line if there are still troubles

Others

E1

EXX

E2

Check the water tap is 
opened or not.

Check the water level 
sensor and drain pump.

Alarm for abnormal 
water intaking.

Alarm for water drain 
has not finished.

Alarm for lid not closed 
before wash and spin.

E3

Closed the lid.

E4

Manually balance clothes
in the barrel by hands.

Alarm for washing stay 
at one side. 

Summary of Contents for DMWM80






















Reviews: