Middle Atlantic Products MM3-C Series Instruction Sheet Download Page 11

ADJUSTMENTS

Pitch Adjustment

1. Adjust pitch to desired tilt position. (See Figure K)

2. Adjust pitch tension screw to change the adjustment tension. (See Figure K)

Pivot Adjustment

3. Adjust pivot position as desired. (See Figure K) 

4. Use 3/16” hex key (Y) to adjust pivot point tension screws to change pivot adjustment tension. (See Figure K)

                                                                              FIGURE K
Rotational Adjustment

NOTE:  

(OPTIONAL) Rotational adjustment may be locked by installing rotational locking screw (V) into back of 

faceplate. (See Figure L)

5. The monitor may be adjusted 90 degrees in either direction in order to provide a portrait view of the monitor. 

(See Figure L)

6. Use 3/16” hex key (Y) to adjust rotational adjustment screw to adjust rotational tension. (See Figure L)

Lift Arm Tension Adjustment

1. Tension may be adjusted with tension adjustment screw inside cable management cover and 1/8” hex key 

(X). Turn clockwise to reduce tension or counter-clockwise to increase tension. (See Figure M)

                       

Pitch 

Pivot point

tension

tension

5

1

3

Rotational tension

6

(V)

                  FIGURE L

                  FIGURE M

Reduce tension

Increase tension

(lighter display)

(heavier display)

Do NOT over-tension

adjustment tension
screw.

                  FIGURE M

Page 11

Summary of Contents for MM3-C Series
















Reviews: