Technical data
blind zone
operating range
maximum range
angle of beam spread
20 mm
150 mm
30 mm
250 mm
250 mm
see detection zone
350 mm
see detection zone
transducer frequency
resolution
reproducibility
detection zones
for different objects:
The dark grey areas represent the zone
where it is easy to recognise the normal
reflector (round bar). This indicates the typical
operating range of the sensors. The light
grey areas represent the zone where a
very large reflector – for instance a
plate – can still be regognized. The
requirement here is for an optimum
alignment to the sensor. It is not
possible to evaluate ultrasonic
reflections outside this area.
380 kHz
0.069 mm
320 kHz
0.069 mm
± 0.15 %
± 0.15 %
accuracy
operating voltage U
B
voltage ripple
no-load current consumption
±1 % (temperature drift internally compensated)
10 - 30 V DC, reverse polarity protection (Class 2)
±1 % (temperature drift internally compensated)
10 - 30 V DC, reverse polarity protection (Class 2)
±10 %
< 40 mA
±10 %
< 40 mA
housing
ECOLAB
class of protection per EN 60 529
stainless steel 1.4404/316L;
ultrasonic transducer: PTFE, FKM
stainless steel 1.4404/316L;
ultrasonic transducer: PTFE, FKM
yes
IP 67
yes
IP 67
norm conformity
type of connection
controls
EN 60947-5-2
EN 60947-5-2
4-pin M8 initiator plug
Teach-in via pin 2 (Com)
4-pin M8 initiator plug
Teach-in via pin 2 (Com)
programmable
operating temperature
storage temperature
switched output
Teach-in, LinkControl
-25°C to +70°C
Teach-in, LinkControl
-25°C to +70°C
-40°C to +85°C
Push-Pull, U
B
-3 V, -U
B
+3 V, I
max
= 100 mA
-40°C to +85°C
Push-Pull, U
B
-3 V, -U
B
+3 V, I
max
= 100 mA
switching hysteresis
1)
switching frequency
1)
response time
1)
switchable NOC/NCC, short-circuit-proof
2 mm
switchable NOC/NCC, short-circuit-proof
3 mm
25 Hz
32 ms
25 Hz
32 ms
time delay before availability
1)
weight
order no.
< 300 ms
30 g
< 300 ms
30 g
pms-15/CF/A1
pms-25/CF/A1
1) Can be programmed with LinkControl
65 mm
350 mm
120 mm
1,000 mm
600 mm
see detection zone
1,300 mm
see detection zone
400 kHz
0.069 mm
200 kHz
0.069 mm
± 0.15 %
± 0.15 %
±1 % (temperature drift internally compensated)
10 - 30 V DC, reverse polarity protection (Class 2)
±1 % (temperature drift internally compensated))
10 - 30 V DC, reverse polarity protection (Class 2)
±10 %
< 40 mA
±10 %
< 40 mA
stainless steel 1.4404/316L;
ultrasonic transducer: PTFE, FKM
stainless steel 1.4404/316L;
ultrasonic transducer: PTFE, FKM
yes
IP 67
yes
IP 67
EN 60947-5-2
EN 60947-5-2
4-pin M8 initiator plug
Teach-in via pin 2 (Com)
4-pin M8 initiator plug
Teach-in via pin 2 (Com)
Teach-in, LinkControl
-25°C to +70°C
Teach-in, LinkControl
-25°C to +70°C
-40°C to +85°C
Push-Pull, U
B
-3 V, -U
B
+3 V, I
max
= 100 mA
-40°C to +85°C
Push-Pull, U
B
-3 V, -U
B
+3 V, I
max
= 100 mA
switchable NOC/NCC, short-circuit-proof
5 mm
switchable NOC/NCC, short-circuit-proof
20 mm
12 Hz
64 ms
10 Hz
80 ms
< 300 ms
30 g
< 300 ms
30 g
pms-35/CF/A1
pms-100/CF/A1
+U
B
-U
B
F
1
2
4
3
Push-Pull output in pnp circuit
U
+U
B
-U
B
F
1
2
4
3
Push-Pull output in npn circiut
U
Com
Com
pms-15...
pms-25...
8 cm
4 cm
0 cm
4 cm
8 cm
0 cm
4 cm
8 cm
12 cm
16 cm
20 cm
24 cm
Rohr ø 10 mm
ausgerichtete Platte
Plate
Rohr ø 10 mm
8 cm
0 cm
4 cm
8 cm
4 cm
8 cm
4 cm
0 cm
4 cm
8 cm
0 cm
4 cm
8 cm
12 cm
16 cm
20 cm
24 cm
Rohr ø 10 mm
ausgerichtete Platte
Round bar ø 10 mm
8 cm
0 cm
4 cm
8 cm
4 cm
0 cm
4 cm
8 cm
12 cm
16 cm
20 cm
24 cm
0 cm
5 cm
10 cm
15 cm
20 cm
25 cm
30 cm
35 cm
Plate
Round bar ø 10 mm
10 cm
5 cm
0 cm
5 cm
10 cm
pms-35...
pms-100...
0 cm
10 cm
20 cm
30 cm
40 cm
50 cm
60 cm
Plate
Round bar ø 27 mm
20 cm
10 cm
0 cm
10 cm
20 cm
35 cm
0 m
0,2m
0,8 m
1,0 m
1,3 m
0,4 m
0 m
0,4 m
0,6 m
0,4 m
1,0 m
1,4 m
0,2 m
0,2 m
Round bar ø 27 mm
Plate
arrangement of the sensors shown
in figure 2 must be maintained.
The pms sensors are equipped
with an internal temperature com-
pensation. Due to the sensors self
heating, the temperature compen-
sation reaches its optimum work-
ing-point after approx. 45 seconds
of operation.
In the »Set detect point – method
A« Teach-in procedure the actual
distance to the object is taught to
the sensor as the detect point. If
the object moves towards the
sensor (e.g. with level control) then
the taught distance is the level at
which the sensor has to switch the
output.
If the object to be scanned moves
into the detection area from the
side, the »Set detect point +8 % –
method B« Teach-in procedure
should be used. In this way the
switching distance is set 8 % fur-
ther than the actual measured dis-
tance to the object. This ensures a
reliable switching distance even if
the height of the objects varies
slightly.
Fig. 4: Setting the detect point for different
directions of movement of the object
The sensor can be reset to its fac-
tory setting (see »Further set-
tings«).
For Teach-in procedure when us-
ing the LinkControl adapter (op-
tional accessory) the additional
adapter 5G/M12-4G/M12/M8 is
needed.
If the sensor is cleaned wet during
operation, all surfaces must be in-
clined at least 3° from the hori-
zontal alignment so that the clea-
ning agents can run off completely
(see figure 3).
Ordertel 08-771 00 04
Växel
08-771 02 20
Orderfax 08-771 62 00
Teknisk 08-771 35 80
Länna, S-142 50 SKOGÅS (Stockholm)
www.hemomatik.se
