manualshive.com logo in svg

MicroNet SP916GN, User Manual

Share
Download
MicroNet SP916GN User Manual Download Page 23

 

Connection Type 

z

 

If you select “Continuous”, the router will always connect to 
the ISP. If the WAN line breaks down and links again, the 
routers will auto-reconnect to the ISP.  

z

 

If users select “Connect on Demand”, the router will auto-
connect to the ISP when someone wants to use the Internet 
and keep connected until the WAN idle timeout. The router 
will close the WAN connection if the idle time period exceeds 
the “Idle Time”. 

z

 

If users select “Manual”, the router will connect to ISP only 
when click “Connect” manually from the Web user interface. 
The WAN connection will not disconnect due to the idle 
timeout. If the WAN line breaks down and links again, the 
router will not auto-connect to the ISP. 

Idle Time 

z

 

Users can specify an idle time threshold (minutes) for the 
WAN port. This means if no packets have been sent during 
the specified period, the router will automatically disconnect 
the connection with the ISP. 

Click <OK> to complete the Quick Setup Wizard and start using the broadband 

router. 

 

Step 2.4 PPTP xDSL 

Select PPTP if the ISP requires the PPTP protocol to connect to the Internet. The 

ISP should provide all the information required in this section. 

 

 

 

 

20

Summary of Contents for SP916GN














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands