manualshive.com logo in svg

MicroNet SP916GN, User Manual

Share
Download
MicroNet SP916GN User Manual Download Page 22

 

Parameter 

Description 

IP 

IP address provided by ISP. 

Gateway IP 

ISP’s IP address gateway. 

DNS 

ISP’s DNS server IP address. 

Subnet Mask 

Enter the Subnet Mask provided by the ISP (e.g. 255.255.255.0).

Click <OK> to complete the Quick Setup Wizard and start using the broadband 

router. 

 

Step 2.3 PPPoE xDSL 

Select PPPoE if the ISP requires the PPPoE protocol to connect to the Internet. The 

ISP should provide all the information required in this section. 

 

  

Parameter 

Description 

Username 

Enter the username provided by the ISP for the PPPoE 
connection. 

Password 

Enter the password provided by the ISP for the PPPoE 
connection. 

Service Name 

This is optional. Enter the Service name should the ISP requires 
it, otherwise leave it blank. 

MTU 

This is optional. Users can specify the maximum size of the 
transmission packet to the Internet. Leave it blank if users do not 
wish to set a maximum packet size. 

 

19

Summary of Contents for SP916GN














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands