Microhard Systems pX2 Operating Manual Download

Page: 98 / 141

5.0 AT Command Line Interface

ATO

Command Syntax (Effect: Immediate)

Quit. Exits AT Command session and returns you to
login prompt.

ATO <enter>

Description

Example

Input:

ATO <enter>
Response:

OK
PX2 Login:

AT+MSCNTO

Command Syntax (Effect: AT&W)

Sets the timeout value for the serial and telnet
consoles. Once expired, user will be return to login
prompt.

AT+MSCNTO=<Timeout_s>

0 - Disabled
0 - 65535 (seconds)

Description

Example

Input:

AT+MSCNTO=300 <enter>
Response:

AT+MSPWD

Command Syntax (Effect: Immediate)

Used to set or change the ADMIN password.

AT+MSPWD=<New password>,<confirm
password>

password: at least 5 characters

Description

Example

Input:

AT+MSPWD=admin,admin<enter>
Response:

Summary of Contents for pX2














































































































































Search results

Summary of Contents for pX2

Reviews:

Related manuals for pX2

Brands by name

Popular brands

Microhard Systems pX2, Operating Manual

Search results

Summary of Contents for pX2

Reviews:

Related manuals for pX2

Brands by name

Popular brands