background image

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME COUNTRIES DO NOT 
ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OF 
INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE 
ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS 
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM 
COUNTRY TO COUNTRY. NOTHING IN THIS WARRANTY SHALL BE TAKEN TO 
AFFECT YOUR STATUTORY RIGHTS. 
 

Firmware and Drivers 

For latest driver, technical information and bug-fixes please visit 

www.eControlSystems.com

 or 

call (818) 885-5228. 
 

Statement of Conditions 

In line with our continued efforts to improve internal design, operational function, and/or 
reliability, ECS reserves the right to make changes to the product(s) described in this document 
without notice. ECS does not assume any liability that may occur due to the use or application of 
the product(s) described herein. In order to obtain the most accurate knowledge of installation, 
bug-fixes and other product related information we advise to visit the relevant product support 
page at www.eControlSystems.com before you start installing the equipment. All information is 
subject to change without notice. 

 

Limitation of Liability 

In no event, whether based in contract or tort (including negligence), shall ECS be liable for 
incidental, consequential, indirect, special or punitive damages of any kind, or for loss of revenue, 
loss of business or other financial loss arising out of or in connection with the sale, installation, 
maintenance, use, performance, failure or interruption of its products, even if ECS or its 
authorized reseller/distributor has been advised of the possibility of such damages. 

 

Copyright 

Information furnished by E-Control Systems, Inc. (ECS) is believed to be accurate and reliable. 
However, no responsibility is assumed by ECS for its use, nor for any infringements of patents or 
other rights of third parties which may result from its use. No license is granted by implication or 
otherwise under any patent or patent rights of ECS. ECS reserves the right to change 
specifications at any time without notice. 

 

Trademarks 

MicroGate, Raptor Web Software, and Online Kitchen are trademarks of E-Control Systems, Inc. 
Other product and company names are trademarks or registered trademarks of their respective 
holders. 
 

MicroGate™ User Manual                                                                                                18 

Summary of Contents for MicroGate MG1-1000



















Reviews: