background image

Ubee Interactive — www.ubeeinteractive.com 

 

 

 

  Ubee DVW32CB – Safety and Installation Product Insert v1.0 

DVW32C Advanced Wireless Voice 
Gateway - Safety and Installation 
Product Insert 

 

Federal Communications Commission 
(FCC) Interference Statement

 

This equipment has been tested and found to 
comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These 
limits are designed to provide reasonable 
protection against harmful interference in a 
residential installation. This equipment generates, 
uses and can radiate radio frequency energy and, 
if not installed and used in accordance with the 
instructions, may cause harmful interference to 
radio communications. However, there is no 
guarantee that interference will not occur in a 
particular installation. If this equipment does 
cause harmful interference to radio or television 
reception, which can be determined by turning 
the equipment off and on, the user is encouraged 
to try to correct the interference by one of the 

following measures: 



Reorient or relocate the receiving antenna 



Increase the separation between the 
equipment and receiver. 



Connect the equipment into an outlet on a 
circuit different from that to which the receiver 
is connected.   



Consult the dealer or an experienced radio/TV 
technician for help. 

FCC Regulatory Information 

This device complies with Part 15 of the FCC 
Rules. Operation is subject to the following two 
conditions: (1) This device may not cause 
harmful interference, and (2) this device must 
accept any interference received, including 
interference that may cause undesired operation. 

There is one statement for this product:   



Only the type of PCB PIFA antenna tested 

Summary of Contents for DVW32CB








Reviews: