Microframe Corporation RX10 Operating Manual Download | Manualshive

Page: 10 / 16

background image

10 of 10

RX10 Ten-Zone Receiver Decoder

b) General Set Up

“File Name” and “Build” are read-only fields. Data will appear in the boxes after a file is saved or opened.

The baud rate and data polarity must be chosen to match the settings of the transmitter used with the
system.

«
...
8
9
10
11
12
...
»

Summary of Contents for RX10

















Reviews:

No comments

Related manuals for RX10

Brand: CYP Pages: 12

LS001-W100E2-AA-M4PK1

Brand: Harbor Breeze Pages: 2

Multimedia Enclosure ME3

Brand: Emprex Pages: 40

Scan Converter VSC 500

Brand: Extron electronics Pages: 2

Brand: J-Tech Digital Pages: 34

Brand: Vortex Pages: 179

Brand: 3onedata Pages: 2

Brand: Yarvik Pages: 64

Brand: J-Tech Digital Pages: 5

Brand: Acromag Pages: 17

Brand: Ewind Pages: 3

Brand: Fairport Pages: 9

Brand: 3One data Pages: 2

Brand: Sandi Electric Pages: 32

SUN-6K-SG05LP1-EU

Brand: V-TAC Pages: 57

Brand: DeWalt Pages: 37

Brand: Black Box Pages: 2

Mini VGA+3.5 Audio to HDMI Adapter

Brand: Gaia Vision Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands