Microframe Corporation
Series 3500 - MultiPage System
17
6 NEXUS PAGER
6.1 TURNING ON THE PAGER
Hold down the RED BUTTON on the side
until the pager comes on.
6.2 SENDING A PAGE
Please see the diagram in the MultiPage
section of this manual for detailed instructions
on sending pages.
6.3 ACTIVATING AN ALPHA MES-
SAGE
To activate a pre-defi ned message to a Vibrat-
ing Pager, type in the Pager number followed
by the
"SEND"
key. You will be prompted for
a “BEEP TYPE (1-4).” Select 1-3 here and
press the
“SEND”
key. This will display on the
Pager one of the three pre-programmed text
messages stored in the Pager. If no number is
chosen, the Pager will default to Beep Type 4
(“PAGING”).
6.4 SENDING A NUMERIC MESSAGE
To send a numeric message to a Pager,
simply type in the Pager number followed by
the
“SEND”
key. The Transmitter screen will
display “BEEP TYPE.” Simply press
“ENTER”
to bypass this. The Transmitter screen will
then display “ENTER MESSAGE.” Using the
number keys, type in a numeric message up to
16 digits followed by the
“SEND”
key. Note:
If the message portion of a page is not blank
the “BEEP TYPE” alpha message selected will
be ignored.
6.5 RECEIVING A PAGE
The Pager will start to vibrate when it is
paged. No action is necessary on the receiving
end. The Pager will stop vibrating after approxi-
mately eight seconds. If the user would like
to stop the vibration before the eight seconds,
simply press the RED BUTTON on the side of
the pager. If a numeric message is sent to the
Pager, the message will be visible on the Pager's
LCD screen until the pager stops vibrating. To
view the message and turn off fl ashing lights,
press the RED BUTTON three times.
6.6 SENDING A GROUP CALL PAGE
All pagers respond to call number “900”
(unless another group call number has been
chosen by the customer and programmed at
the factory). To page all pagers at once, simply
enter “900” and
"SEND."
Then press
"SEND"
again at the beep type prompt.
6.7 MANUAL PAGER TURN-OFF
Press the RED BUTTON on the side of
the pager for 5 seconds or place pager on the
charging base.
6.8 LIGHTING FUNCTION
Press the RED BUTTON on the side of
pager.
6.9 CHANGING THE ALERT MODE
Pagers may be programmed to respond to a
page by fl ashing lights, fl ashing and beeping,
fl ashing and vibrating, or fl ashing, vibrating
and beeping. By default, the pagers are pro-
grammed to fl ash and vibrate for 8 seconds.
To change the alert mode, follow these
instructions: Remove all the pagers from the
charging unit or unplug the power supply that
is connected to the charging base. Wait for the
demo page to stop (about 7 seconds). Press
"1248" followed by "SEND" and "ENTER." For
the message, enter the code that corresponds
to the alert that you want. (See below.) For
example, if you want the pagers to Flash only,
press "1248-SEND-ENTER-9797-SEND." After
sending the code, the lights on all the pagers
will fl ash to indicate the programming was
received. Return all the pagers to the charg-
ing base or plug the power supply back in. The
pagers are ready to receive the page with the
new alert.
Flash & Beep
"9595"
Flash & Vibrate
"9696"
Flash Only
"9797"
Flash, Vibrate & Beep
"9898"
6.10 CAUTION
a) The
pager is made up of LCD and
precision elements. Avoid water and
high temperature.
b) If
the pager is not working properly,
do not dismantle or repair it yourself.
Call Microframe for technical service.
