manualshive.com logo in svg

MicroComm DXL TMM-640, Installation Instructions Manual

Share
Download
MicroComm DXL TMM-640 Installation Instructions Manual Download Page 9

TMM-640 VoIP Touchscreen Master Module 

 

Document IM-TMM-640-1.2 

 

Page 9 

8.

 

Using a web browser to configure the TMM-640 

Once the IP address of the TMM-640 has been determined and connected to an Ethernet network, a PC on the 

same network can access the TMM-640 and use a web browser to set the remaining parameters necessary to make 

the TMM-640 work in a DXL system. 

The first step is to hook up the bottom Ethernet port on the master to a network switch. Once the master has reset 

and the LED on the front is flashing green, you can bring up a web browser from a PC on the same network (that 

is assigned an IP address within the same network mask as the TMM-640). 

In the address bar, type “

http://<address of master>

”. For example, if the master is 10.0.0.56, type 

“

http://10.0.0.56

”. This will bring up a MicroComm DXL master setup page. 

If this is not the first time that the web browser has been used to configure the TMM-640 after a factory reset, the 

TMM-640 will skip the MicroComm Setup Wizard screens and go directly to the web browser menus. The user 

will have to sign in as the administrator (using the password assigned during initial configuration) to make 

changes to these settings. If this is the first setup after a factory reset then the user will have to enter some 

information before being allowed to go directly to the web browser menus. The following section describes the 

MicroComm Setup Wizard screens and how to configure them. The section after that describes the settings to 

make in the web browser menus. 

8.1

 

Using the MicroComm Setup Wizard 

If this is the first time that the TMM-640 has been configured with a web browser, the following screen will come 

up. If this screen is not shown, then the TMM-640 was likely previously configured, in which case you can skip to 

the next section. 

 

Click the “

Start Setup Wizard

” button to continue. 

Summary of Contents for TMM-640


























Reviews:

No comments

Brands by name

Popular brands

Load more brands