manualshive.com logo in svg

MicroComm DXL TMM-640, Installation Instructions Manual

Share
Download
MicroComm DXL TMM-640 Installation Instructions Manual Download Page 3

TMM-640 VoIP Touchscreen Master Module 

 

Document IM-TMM-640-1.2 

 

Page 3 

1.

 

Intent & Scope 

This document describes the installation and setup procedures for the DXL TMM-640 VoIP Touchscreen Master 

Module.  

2.

 

Description 

The TMM-640 is a small desktop style intercom master station for use with a touchscreen terminal. It is aVoice 

over Internet Protocol (VoIP) device that implements the industry standard Session Initiation Protocol. The TMM-

640 connects to an exchange via the inter-exchange Ethernet network. 

The TMM-640 includes a speaker (c/w volume adjustment) an electret microphone, a push-to-talk(PTT) switch, 

and a LED status indicator. A front panel 2.5 mm jack allows a variety of wired headsets to be utilized.  

The TMM-640 also provides contacts for an external PTT (foot) switch as well as a privacy handset, and includes a 

3.5 mm stereo output jack to provide line-level signaling for external amplified speakers 

The TMM-640 is powered by a wall adapter power supply (normally included with the TMM-640) or through 

Power over Ethernet (PoE) if you have a PoE capable network switch. 

The functional operation of the TMM-640 in a DXL system is carried out using the Administrator Software and 

the DCC software. Three procedures are required to configure a TMM-640 master station: 

1. 

Configuring an IP Master using the Administrator 

2. 

Use DHCP to set the IP Address of the TMM-640 master station 

3. 

Use a web browser to configure the TMM-640 master station to operate with the MicroComm system. 

The following diagram shows the location of the connectors on the TMM-640. 

Summary of Contents for TMM-640


























Reviews:

No comments

Brands by name

Popular brands

Load more brands