MicroComm DXL TMM-640 Installation Instructions Manual Download Page 20 | Manualshive

Page: 20 / 25

MicroComm DXL TMM-640 Installation Instructions Manual Download Page 20

TMM-640 VoIP Touchscreen Master Module

Page 20

Document IM-TMM-640-1.2

Next, click on the

System

tab on the menu bar.

Most of these

System Settings

were previously entered in the MicroComm Setup Wizard, but a brief description

of the settings is below if you need to change them after the initial setup.

Time Server (NTP)

is the IP address or Domain Name of a Network Time Protocol (NTP) server. This can be used

by the TMM-640 master to set its clock time to same time as the NTP server. This should be left blank for most

cases.

GMT Offset (hours)

should be set to the time zone that the TMM-640 will be used in.

Workgroup Key

should be set to the workgroup name used by all of the IP masters in the MicroComm system.

While the

Workgroup Key

setting for the network can be any value you choose, all IP masters should have the

same

Workgroup Key.

If you have made any changes, click “

Update

”.

«
...
18
19
20
21
22
...
»

Summary of Contents for TMM-640


























Reviews:

No comments