MICRO-EPSILON colorCONTROL MFA-5 Instruction Manual Download Page 29

Page: 29 / 80

Page 29

Operation

colorCONTROL MFA-5

The functions of the individual control elements are explained in the following steps, see

Fig. 20

Fig. 20 Start screen extract

Connect Button

The colorCONTROL MFA-5 is connected to the software after pressing the

Con-

nect

button. In doing so, the button label changes to

Disconnect

. The color-

CONTROL MFA-5 is disconnected after pressing the button again.

Not Connected label

Shows the respective connection status of the colorCONTROL MFA-5.

Start Test button

The software performs a test using the current test configuration.

Select Board

Enables the selection of the connected colorCONTROL MFA-5 sensors.

Select LED

Enables the selection of a specified checkpoint / specified color chip on the

colorCONTROL MFA-5.

Summary of Contents for colorCONTROL MFA-5

















































































Search results

Summary of Contents for colorCONTROL MFA-5

Reviews:

Related manuals for colorCONTROL MFA-5

Brands by name

Popular brands

MICRO-EPSILON colorCONTROL MFA-5, Instruction Manual

Search results

Summary of Contents for colorCONTROL MFA-5

Reviews:

Related manuals for colorCONTROL MFA-5

Brands by name

Popular brands