background image

KSZ8864 Evaluation Board User’s Guide 

Micrel Inc. 

Page 4 

5/9/2014 

 

1.0 Introduction 

The KSZ8864 is Micrel Operations’ new generation integrated 4-port switch with a 64-pin small 
package. The KSZ8864 device consists of two PHYs and four MACs. Two of MACs support either 
MII or RMII interfaces for dual processor/DSP data transfer. Higher speed SPI and MDC/MDIO 
interfaces can fully manage the 4-port switch by the processor. The device had been designed with 
cost sensitive systems in mind but still offers a multitude of features such as switch management; 
port and tag based VLAN; 1/2/4-queue QoS priority; a dual MII/RMII option data interfaces and 
CPU control interfaces of SPI, MDC/MDIO with MIIM/SMI. MIIM is the standard IEEE 802.3 
MII Management Interface. SMI is non-standard Serial Management Interface that can access all 
registers by the Management Data Input/output MDIO interface.  The KSZ8864 is an excellent 
choice in current complex Ethernet applications with single processor or dual processors, industrial 
automatic, automotive, etc. fields and as a standalone 4-port switch.  

The KSZ8864 evaluation board is designed to allow the user to experience first-hand the rich 
feature set of these existing 4-port switches of KSZ8864CNX/RMNUB. The evaluation board is 
highly configurable and easy to use.  

2.0 Features  

 

Micrel KSZ8864 Integrated 4-port 10/100 Managed Ethernet Switch  

 

2 RJ-45 Jacks for Ethernet LAN with Corresponding Isolation Magnetics.  

 

Auto MDI/MDIX on all Ports.  

 

1 PHY mode and 1 MAC mode 40-pin male/female connectors are for the port 3 Switch 
SW3-MII/RMII Interfaces. 

 

1 PHY mode and 1 MAC mode 40-pin male/female connectors are for the port 4 Switch 
SW4-MII/RMII Interfaces. 

 

1 USB Port Interface Configurable to emulate interfaces of EEPROM, SPI interface, 
MDC/MDIO with SMI Interface and access all MIIM registers.   

 

On Board EEPROM  

 

2 LEDs Per Port to Indicate the Status and Activity  

 

5VDC, 2.5A Universal Power Supply  

3.0 Evaluation Kit Contents  

The KSZ8864 Evaluation kit includes the following:  

 

KSZ8864 Evaluation Board Rev. 1.x 

 

KSZ8864 Evaluation Board User’s Guide Rev 1.x 

 

Micrel EEPROM/SPI/SMI/MIIM Configuration Software  

 

KSZ8864 Evaluation Board Schematics and BOM  

 

The software, schematics and other design information will be found in the hardware design 
package in the Design Kit of the KSZ8864 Ethernet switch product on Micrel website. 
(Contact your Micrel FAE for the latest schematic). 

 

The USB cable is not included. 

Summary of Contents for KSZ8864





























Reviews: