background image

KSZ8864 Evaluation Board User’s Guide 

Micrel Inc. 

Page 15 

5/9/2014 

5.0 Software Description 

5.1 Introducing Application Software Tools 

The Design Kit provides some software tools to support SPI interface, EEPROM (I2C) and 
MDC/MDIO access for MIIM registers and SMI interface. They are located folders in the software 
tool directory as follows: 

1.

 

In folder of DOS SPI Tool, there is an 8895SPI_DOS.exe file which can be executed 
directly. The tool is used to access all registers by SPI in a DOS Window.  

2.

 

In folder of MDC_MDIO SMI, there is a MicrelSMIIfApp.exe file which can be executed 
directly by clicking its icon. The software tool is used to access all registers by MDC/MDIO 
interface with SMI mode. 

3.

 

In folder of Window SPI_I2C_MIIM Tools, there is a MicrelSwitchPhyTools_1.xx.msi file 
which is clicked to create two application files in the default folder of Micrel (or you 
selected folder) and two icons on desktop, they need window drivers supported first, see 5.2 
section for detail. One software tool is used to access all registers by SPI interface or is used 
to read/write all control register on I2C EEPROM mapping. Another software tool is used to 
access all MIIM registers for all PHYs. 

4.

 

All of application files after installation .msi file 

 

5.2 Install Window Driver First 

Before use the Window based application software tool, the support drivers need to be installed to 
PC/Laptop first and this installation is just one times only. When connect one standard USB cable 
with type A and type B connectors between the evaluation board and PC computer first time, the 

Summary of Contents for KSZ8864





























Reviews: