background image

EDM-MD Series 
Installation Manual

 

 

 

 

 

Page 12

 

 

 

 

3.4 Mounting Doors 

-

 

Position hanger roller brackets on top of door leaf. 

-

 

Ensure hanger brackets are aligned, then secure in place. 

-

 

Loosen hanger bracket retainer to mount doors on rail.  

-

 

Mount doors on rail. 

-

 

Adjust and secure hanger bracket retainer 2mm from underside of base rail. 

-

 

Adjust door height for floor clearance. 

-

 

Check door alignment to eliminate gaps before tightening fully.  

3.5 Smooth Operation 

-

 

Check opening and closing of door leaf with power off.  

-

 

Doors must run smoothly without friction or noise.  

-

 

Doors should be easy to push open and close. 

-

 

Check clearance from finished floor level (open & close). 

3.6 Power On  

Caution – Before switching the power on: 

-

 

Rail and doors are correctly installed 

-

 

Ensure tooth belt is tightened 

-

 

Main parts are correctly installed - Refer to wiring diagrams. Sec. 8. 

The power switch is located to the right of motor fixed to the underside of the base rail.  

4. Teaching / Learning Operation 

 

CAUTION: Ensure that the door travel area is clear before pressing RESET in order to memorize the 
door stroke.

 

 

4.1

 

Teaching / Learning 

After installation is completed, in order to memorize the door stroke by a teaching or learning stoke. The following 
steps are required.  

-

 

Set the slide switch (Prog / Run) down to “PROG”.  

-

 

Press and hold the “UP” button & “SET” button together. The RED and GREEN LED will flash once the RESET 
is complete. 

-

 

Set the slide switch up to “RUN” and the door will start to close at low speed.  
Starting from the fully closed position will ensure the doors are correctly optimised.  

-

 

From the fully closed position, the door/s will open at low speed.   
Here EDM MD controller is memorizing the stroke by this cycle. Once at full open, the teaching / learning 
stroke is complete.  The door/s will then close at normal speed. 

Summary of Contents for EDM-MD Series
























Reviews: