MicaSense RedEdge-MX DJI M300 RTK Quick Mount Gen. 2 Integration Manual Download Page 6 | Manualshive

Page: 6 / 13

background image

RedEdge-MX Instructions

Attaching the RedEdge-MX and the Mount

1. Locate the two M3 x 6 mm socket head cap screws, M3 lock washers, and Quick Mount

Gen. 2 Adapter.

2. Using the counterbore screw holes, attach the mount to the back of the RedEdge-MX.

Make sure the mount 8-pin camera port is located on the same side as the camera
“PWR/TRG” port.

3. Connect the provided Quick Mount Gen.2 RedEdge-MX cable to the RedEdge-MX

“PWR/TRG” and “DLS” ports.

Rev 01 - July 2020

PAGE 5

«
...
4
5
6
7
8
...
»

Summary of Contents for RedEdge-MX DJI M300 RTK Quick Mount Gen. 2














Reviews:

No comments

Related manuals for RedEdge-MX DJI M300 RTK Quick Mount Gen. 2

Brand: Veris Industries Pages: 2

Brand: BAC Pages: 10

Brand: Baby’s Journey Pages: 2

Brand: Lanier Pages: 3

Brand: rako Pages: 3

Brand: U-Line Pages: 3

Brand: X4-Life Pages: 2

KTS-WB61141142 Series

Brand: SICK Pages: 8

Brand: SimplyHome Pages: 2

WaterGuard CM2300

Brand: Mobeye Pages: 32

Brand: PROAIM Pages: 3

Brand: UBEXi Pages: 16

Brand: Chillout Pages: 9

Brand: REV Ritter Pages: 8

Brand: Belkin Pages: 4

Brand: Marmitek Pages: 8

Brand: SICK Pages: 46

Brand: Enviro Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands