manualshive.com logo in svg

Mic EC-912, Instruction Manual, Page: 2 / 38

Share
Download
Mic EC-912 Instruction Manual Download Page 2

Instruction Manual MIC type EC-912 

Revision no.4 

2 / 38 

Table of Contents 

 

General information ................................................................................. 5

 

 

Introduction ..........................................................................................................5

 

 

General description ..............................................................................................6

 

 

Applications ..........................................................................................................6

 

 

Specifications .......................................................................................................7

 

 

System specifications ...........................................................................................7

 

 

Measuring Ionization Chamber (MIC) type EC-912-10 .........................................7

 

 

Analog MIC Control Unit (AMCU) type EC-912-20 ...............................................8

 

 

Intelligent MIC Control Unit (IMCU) type EC-912-25 .............................................8

 

 

Flow Control Unit (FCU), type EC-912-40 ............................................................8

 

 

Vacuum Pump (VP), Thomas VTE 3, type EC-999-08 .........................................9

 

 

Installation .............................................................................................. 10

 

 

Preparation for use .............................................................................................10

 

 

Unpacking ..........................................................................................................10

 

 

Mains cord .........................................................................................................10

 

 

Performance check using an Analog MIC Control Unit (AMCU) .........................11

 

 

Performance check using an Intelligent MIC Control Unit (IMCU) .......................11

 

 

Installation of Measuring Ionization Chamber (MIC) ...........................................13

 

 

Installation of Vacuum Pump (VP) ......................................................................15

 

 

Installation of Control Cabinet (CC) ....................................................................15

 

 

Operation ................................................................................................ 16

 

 

Operating controls, connectors and indicators ....................................................16

 

 

Measuring Ionization Chamber (MIC) .................................................................16

 

 

Control Cabinet (CC) ..........................................................................................16

 

 

Analog MIC Control Unit (AMCU) .......................................................................16

 

 

Intelligent MIC Control Unit (IMCU) ....................................................................17

 

 

Flow Control Unit (FCU) .....................................................................................17

 

 

Vacuum Pump (VP)............................................................................................17

 

 

Smoke density measurements ...........................................................................18

 

 

Measuring set-up ...............................................................................................18

 

 

Measuring procedure with AMCU .......................................................................18

 

 

Theory of operation ............................................................................... 20

 

Summary of Contents for EC-912







































Reviews:

No comments