background image

4

Safety

WARNING!

Installation  and

service  must  be

performed  by  a

qualified  licen-

sed  installer  or

service agent.

The information in this manual should be fol-

lowed exactly to prevent damage or personal

injury.

Turn off electrical power to unit before servic-

ing. Electric shock could cause personal injury

or death.

For  your  safety  do  not  use  gasoline  or  other

flammable vapors and liquids in the vicinity of

this unit or any other appliance.

If the information in this manual is not follow-

ed  exactly,  a  fire  or  explosion  may  result

causing  property  damage,  personal  injury  or

loss of life.

RISK OF DAMAGE, INJURY AND LOSS OF LIFE

– Improper  installation,  adjustment,  alter-

ation,  service  or  maintenance  can  cause

property  damage,  personal  injury,  or  loss

life.  A  qualified  installer  or  service  agency

must perform installation and service.

RISK OF ELECTRICAL SHOCK – Unit may have

multiple power supplies. Turn the electrical

power of the  unit “OFF” and disconnect

switch(es) before attempting to perform any

service or maintenance.

RISK OF INJURY FROM HOT PARTS – Discon-

nect all power, close all isolation valves, and

allow  equipment  to  cool  before  servicing

equipment with hot water or steam heating

coils.  Hot  water  will  circulate  even  after

power is off. Equipment may have multiple

power supplies.

RISK  OF  INJURY  FROM  MOVING  PARTS –

Disconnect all power before servicing motor

or blower to prevent serious injury resulting

from  automatic  starts.  Motor  and  blower

may have multiple power supplies.

Personal injury and/or equipment damage may result if installation and/or service are not handled properly.

Summary of Contents for HPX Series













Reviews: