MHSC BVPNSC Installation & Operating Instructions Manual Download Page 25

20301938

25

B-Vent Specialty Gas Fireplaces

SIGNATURE COMMAND SYSTEM OPERATION INSTRUCTIONS

 

Function 

Operation 

Default Setting

 

Intermittent/Standing 

Hold the ON 

 button while turning on the master switch 

Intermittent

  Pilot Setup 

(Beep once for standing pilot, twice for intermittent pilot) 

Pilot

  Standing Pilot Temp. 

Hold the ON 

 button 3 seconds (when the master switch

  Shutoff 

on the main burner is off)

  RF Remote Receiver 

Push the RF receiver On/Off button on the control board 

RF OFF   

  On/Off 

Beep once for ON and beep twice for OFF

  Learn Remote 

Hold the OFF 

 button while turning on the master switch

  Transmitter 

(Beep twice then press any handheld remote button)

  6-hour safety  

Press the ON 

 button and OFF 

 button simultaneously 

ON

  shutdown setup 

(Beep once for ON, twice for OFF)

SYSTEM CONFIGURATION/SETUP

All System configuration/setup is done on the Command Center.

NOTE:

 When using On/Off wall switch, the switch must be in the ON position to perform all configuration set 

ups at the command center.

Intermittent/Standing Pilot Setup (Default intermittent)

1.  Holding the ON button on the Command Center while turning on the master switch will toggle between stand-

ing pilot and intermittent pilot. 

2.  After the above operation, one beep (for standing pilot) or two beeps (for intermittent pilot) will be given as 

confirmation.

Six-hour Safety Shutdown Option (Default ON)

1.  The system comes preset from the factory with a six (6) hour shutdown from its last command of operation. 

This is done to prevent the fireplace from continuing to operate if unattended. You may disable this feature 

if you wish.

NOTE:

 By disabling this feature, your fireplace may continue to operate unattended.

2.  When the master switch is in the ON position (“-”), pressing the ON button and the OFF button on the Com-

mand Center simultaneously will toggle between enabling and disabling the six-hour shutdown option. 

3.  After the above operation, one beep (for enabling the six-hour shutdown option) or two beeps (for disabling 

the six-hour shutdown option) will be given as confirmation.

Remote Transmitter Learn Function (Default OFF)

1.  The RF receiver button located on the Control Board must be in the on position before the learn function can 

begin. Use paper clip to depress button. One beep for RF receiver ON or two beeps for RF receiver OFF will 

be given as confirmation. Refer to Figure 18 for location.

2.  After the RF receiver is on, holding the OFF button on the Command Center while turning on the master 

switch will activate the learn function for the transmitter. 

3.  After the above operation, two beeps will be given and the green LED on the Command Center will flash for 

10 seconds. 

4.  During the 10 seconds, press the OFF button on a transmitter to learn. Another two beeps will be given to 

confirm a successful learning. Refer to transmitter instructions for remote operations.

Shutting Off the Standing Pilot (Temporary Shut Off)

To shut off the standing pilot for service or summer shut down, press and hold the ON button on the Command 

Center for 3 seconds when the master switch is in the ON position (“-”) and the main burner is off.

Note

: Pilot will resume the next time system is turned on.

Key Combinations for System Settings

NOTE: 

When On/Off wall switch is used, it must be in the On position to perform all system setups.

Summary of Contents for BVPNSC





































Reviews: